en
  • English
  • German
  • Chinese
MX.7011 Fast digital I/O with TTL levels - SPECTRUM Instrumentation
MX.7011
Fast digital I/O with TTL levels
Parameter Search Sales Contact Support

THIS PRODUCT IS END-OF-LIFE. Show more about end-life-products policy.

Product:

MX.7011

Fast digital I/O with TTL levels

Description:

The MX.70xx series of fast digital I/O boards offers a resolution between 1 bit and 32 bit with a maximum sampling rate of 125 MS/s (60 MS/s). Every 16 bit / 32 bit of the board can be separately programmed for input or output. The on-board memory of up to 128 MByte can be completely used for recording or replaying digital data. Alternatively the MX.70xx can be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MX.xxxx boards. Therefore the MX.70xx board can be used as an enlargement to analogue boards.

Facts & Features:

  • Up to 125 MS/s at 16 bit
  • Up to 60 MS/s at 32 bit
  • 8, 16 or 32 bit mode
  • 110 Ohm input impedance selectable
  • Inputs 3.3 V and 5 V TTL compatible
  • Up to 128 MByte on-board memory
  • 64 MByte standard memory installed
  • Pattern/Edge/Pulsewidth trigger
  • FIFO mode for input and output
  • Synchronization possible
  • CompactPCI/PXI 3U compatible
  • Supporting PXI star trigger
  • Supporting PXI trigger bus
  • Supporting PXI reference clock

Technical Drawing:

Application examples:

  • Pattern generation for parameter tester
  • A/D converter development
  • Data acquisition at a medical tomograph
  • Production test of IGBT modules
  • CCD sensor simulation

FIFO mode

The FIFO mode is designed for continuous data transfer between measurement board and PC memory (with up to 100 MByte/s) or hard disk. The control of the data stream is done automatically by the driver on interrupt request. The complete installed on-board memory is used for buffer data, making the continuous streaming extremely reliable.

Repeated Output

When repeated output is used the data of the on-board memory is replayed continuously until a stop command is executed or N times. As trigger source one can use the external TTL trigger or the software trigger.

Singleshot Output

When singleshot output is activated the data of the on-board memory is replayed exactly one time. As trigger source one can use the external TTL trigger or the software trigger.

PXI Star Trigger Card (Optional)

The MX.9010 is a special PXI star trigger card designed for the Spectrum PXI products. It allows to route clock and trigger synchronously to all PXI slots that are connected to the star trigger slot. The PXI reference clock is overwritten and external trigger events are synchronized to the sampling clock.

Ring buffer mode

The ring buffer mode is the standard mode of all acquisition boards. Data is written in a ring memory of the board until a trigger event is detected. After the event the posttrigger values are recorded. Because of this continuously recording into a ring buffer there are also samples prior to the trigger event visible: Pretrigger = Memsize - Posttrigger.

External Trigger

All boards can be triggered using an external TTL signal. It's possible to use positive or negative edge also in combination with a programmable pulse width. An internally recognized trigger event can - when activated by software - be routed to the trigger connector to start external instruments.

Gated Replay

The Gated Sampling option allows data replay controlled by an external gate signal. Data is only replayed if the gate signal has a programmed level.

Gated Sampling

The Gated Sampling option allows data recording controlled by an external gate signal. Data is only recorded if the gate signal has a programmed level. In addition a pre-area before start of the gate signal as well as a post area after end of the gate signal can be acquired. The number of gate segments is only limited by the used memory and is unlimited when using FIFO mode.

Multiple Recording

The Multiple Recording option allows the recording of several trigger events with an extremely short re-arming time. The hardware doesn't need to be restarted in between. The on-board memory is divided in several segments of the same size. Each of them is filled with data if a trigger event occurs. Pre- and posttrigger of the segments can be programmed. The number of acquired segments is only limited by the used memory and is unlimited when using FIFO mode.

Multiple Replay

The Multiple Replay option allows the fast repetition output on several trigger events without restarting the hardware. With this option very fast repetition rates can be achieved. The on-board memory is divided in several segments of same size. Each of them is generated if a trigger event occurs.

Pattern Trigger

For every bit of the digital input the pattern trigger defines individually the expected level or sets the bit to don't care'. In combination with pulsewidth counter and edge detection the pattern trigger could be used to recognise a huge variety of trigger events.

Pulsewidth Trigger

Defines the minimum or maximum width that a trigger pulse must have to generate a trigger event. Pulse width can be combined with channel trigger, pattern trigger and external trigger. This makes it possible to trigger on signal errors like too long or too short pulses.

PXI Trigger

The Spectrum cards support star trigger as well as the PXI trigger bus. using a simple software commend one or more trigger lines can be used as trigger source. This feature allows the easy setup of OR connected triggers from different cards.

Timestamp

The timestamp option writes the time positions of the trigger events in an extra memory. The timestamps are relative to the start of recording, a defined zero time, externally synchronized to a radio clock, or a GPS receiver. With this option acquisitions of systems on different locations can be set in a precise time relation.

External Clock

Using a dedicated connector a sampling clock can be fed in from an external system. It's also possible to output the internally used sampling clock to synchronize external equipment to this clock.

PXI Reference Clock

The card is able to use the 10 MHz reference clock that is supplied by the PXI system. Enabled by software the PXI reference clock is feeded in the on-board PLL. This feature allows the cards to run with a fixed phase relation.

Reference Clock

The option to use a precise external reference clock (normally 10 MHz) is necessary to synchronize the board for high-quality measurements with external equipment (like a signal source). It's also possible to enhance the quality of the sampling clock in this way. The driver automatically generates the requested sampling clock from the fed in reference clock.

3rd Party Drivers

A lot of third-party products are supported by the Spectrum driver. Choose between LabVIEW, MATLAB, LabWindows/CVI and IVI. All drivers come with examples and detailed documentation.

Programming Examples

Programming examples for C++, Delphi, Visual Basic, C#, VB.Net, Java, Python, Julia and LabWindows/CVI are delivered with the driver. Due to the simple interface of the driver, the integration in other programming languages or special measurement software is an easy task.

Linux

All cards are delivered with full Linux support. Pre compiled kernel modules are included for the most common distributions like RedHat, Fedora, Suse, Ubuntu or Debian. The Linux support includes SMP systems, 32 bit and 64 bit systems, versatile programming examples for Gnu C++ as well as the possibility to get the driver sources for own compilation.

SBench6

SBench 6 is a powerful and intuitive interactive measurement software. Besides the possibility to commence the measuring task immediately, without programming, SBench 6 combines the setup of hardware, data display, oscilloscope, transient recorder, waveform generator, analyzing functions, import and export functions under one easy-to-use interface.

Windows

This standard driver is included in the card delivery and it is possible to get the newest driver version free of charge from our homepage at any time. There are no additional SDK fees for the classical text-based programming. All boards are delivered with drivers for Windows 7, Windows 8, Windows 10 and Windows 11, all 32 bit and 64 bit.

Related products
Product Channels Max. Samplerate
MX.7005 16 125 MS/s
MX.7010 16 125 MS/s
Other platforms
On different platforms Bus Max. Bus Transfer speed
M2i.7011 PCI-X 245 MByte/s
M2i.7011-Exp PCI Express x1 160 MByte/s
MC.7011 CompactPCI 100 MByte/s
MI.7011 PCI 100 MByte/s

Documents

MX.70xx Datasheet

Data sheet of the MX.70xx family

21.02.2022307 K
MX.70xx Manual

Manual of MX.70xx family

21.02.20223 M
SBench 6 data sheet

Data sheet of SBench 6

15.01.2024999 K
MATLAB Manual

Manual for MATLAB drivers for MI/MC/MX

21.02.202270 K
LabVIEW Manual

LabVIEW Manual for MI/MC/MX.70xx

21.02.2022240 K
SBench 6 Manual

Manual for SBench 6

21.02.20227 M

WINDOWS DRIVER + SOFTWARE

MICX_NT32

MI/MC/MX/PCI.xxx Windows 98/NT 32 Bit Drivers

21.02.2022353 K
MICX_XP (32-bit)

MI/MC/MX/PCI.xxx Windows XP/Vista 32 Bit Drivers

21.02.2022381 K
MICX_XP (64-bit)

MI/MC/MX/PCI.xxx Windows XP/Vista 64 Bit Drivers

21.02.2022579 K
MICX_WIN7_8 (32-bit)

MI/MC/MX/PCI.xxx Windows 7/8 32 Bit Drivers

421.02.2022397 K
MICX_WIN7_8 (64-bit)

MI/MC/MX/PCI.xxx Windows 7/8 64 Bit Drivers

421.02.2022604 K
MICX_WIN10 (32-bit)

MI/MC/MX/PCI.xxx Windows 10 32 Bit Drivers

421.02.2022415 K
MICX_WIN10 (64-bit)

MI/MC/MX/PCI.xxx Windows 10/11 64 Bit Drivers

421.02.2022627 K
c_header

C/C++ driver header and library files

7.0023.02.202443 K
SBench5

SBench 5 Installer

5.3.021.02.20225 M
SBench6 (32-bit)

SBench 6 (32-bit) Installer / Windows 7, 8, 10

6.5.0723.02.202436 M
SBench6 (64-bit)

SBench 6 (64-bit) Installer / Windows 7, 8, 10, 11

6.5.0723.02.202439 M
MATLAB Driver

MI / MC / MX MATLAB driver + examples

21.02.2022714 K
LabVIEW Driver

MI / MC / MX LabVIEW Driver

21.02.20228 M
Examples

MI / MC / MX Examples for C/C++, Delphi, VB, LabWindows/CVI, ...

21.02.2022700 K

LINUX DRIVER + SOFTWARE

Linux Driver Complete

MI / MC / MX Linux 32 bit and 64 bit Drivers

421.02.202218 M
SBench6

SBench 6 Linux 32 (.rpm)

6.5.0723.02.202426 M
SBench6

SBench 6 Linux 64 (.rpm)

6.5.0723.02.202426 M
SBench6

SBench 6 Linux 32 (.deb)

6.5.0723.02.202423 M
SBench6

SBench 6 Linux 64 (.deb)

6.5.0723.02.202422 M
SBench6

SBench6 Jetson (.deb)

6.5.0723.02.20248 M
MICX Examples for Linux

MI / MC / MX Linux Examples (C/C++)

21.02.202253 K

Firmware

Case Studies

Digital Data Logger

Real-time high speed digital data logger for embedded systems

21.02.2022510 K

Product Notes

Trigger and Sync

Trigger, Clock and Synchronization Details at high-speed Digitizers

21.02.20221 M

Application Notes

Contact

On location for you. Choose your region.

Europe USA Asia
Contact Europe
Phone +49 (0)4102 6956-0
Fax +49 (0)4102 6956-66
E-Mail info@spec.de
Contact USA
Phone +1 (201) 562-1999
Fax +1 (201) 820-2691
E-Mail sales@spectrum-instrumentation.com
Contact Asia
Phone +61 402 130 414
E-Mail greg.tate@spectrum-instrumentation.com
Support

Request support. We are happy to help.

Support
powered by webEdition CMS